- (61) 3 9761 7600
- sales@andcorp.com.au
RapidConnect FibreClick One Click Cleaners remove dust and oils from fibre connector end faces with one simple push. Choose the 2.5 mm model for SC, FC and ST connectors or the 1.25 mm model for LC and MU connectors. Each cleaner delivers more than 750 cleaning engagements.
A One Click Cleaner provides a fast, simple and repeatable way to remove dust, oils and other contamination from fibre optic connector end faces. With one mechanical push, the RapidConnect FibreClick One-Click Cleaner advances a specially designed dry cleaning material across the ferrule surface. Therefore, technicians can clean fibre connectors without using alcohol, liquids or separate cleaning wipes.
Contamination remains one of the most common causes of avoidable optical loss and unstable fibre network performance. Even a small particle on a connector end face can obstruct the optical signal or transfer contamination to another connector. Consequently, cleaning should form part of every fibre installation, testing and maintenance procedure.
The RapidConnect FibreClick range includes two cleaner sizes:
Both versions clean connectors installed inside adaptors, faceplates and bulkheads. In addition, the removable dust cap acts as an adaptor for cleaning accessible, unmated connectors. As a result, one tool can support both installed and disconnected connector cleaning.
Each FibreClick cleaner provides more than 750 cleaning engagements. Furthermore, its extended tip helps technicians reach connectors positioned inside adaptors or recessed equipment interfaces. This combination makes the cleaner suitable for fibre installation, commissioning, inspection, fault finding and routine network maintenance.
Fibre optic connectors must align two fibre cores with extremely high precision. When the connector surfaces remain clean and correctly aligned, optical signals can pass between the fibres with minimal disruption. However, dust, oils and other residues can interfere with that connection.
A connector can appear clean to the naked eye while still carrying contamination. Fibre cores are very small, so particles that seem insignificant can cover or approach the signal-carrying region. In addition, oils and films can spread across the ferrule surface and trap further particles.
Contamination can contribute to:
Moreover, contamination can move from one connector to another during mating. A dirty patch lead may contaminate a clean adaptor interface. Similarly, a contaminated test lead can affect every port tested with it. Therefore, connector cleaning protects more than the individual connection being serviced.
A disciplined inspect–clean–inspect process helps reduce these risks. First, inspect the connector with suitable fibre inspection equipment. Next, clean it if contamination appears or if inspection cannot confirm cleanliness. Finally, inspect it again before mating the connector.
The One Click Cleaner supports the cleaning stage of that workflow. However, cleaning should not replace inspection. Instead, technicians should combine both processes wherever inspection equipment and project procedures allow.
The RapidConnect FibreClick range covers the two principal ferrule sizes found across common single-fibre connector formats. Therefore, technicians can select the cleaner according to the connector rather than relying only on the equipment type.
The 2.5 mm FibreClick model suits:
SC, FC and ST connector formats use 2.5 mm ferrules. Consequently, they require a cleaning tool designed around that ferrule and adaptor interface.
The 2.5 mm model can clean a connector through an adaptor, faceplate or bulkhead. In addition, technicians can use the cap arrangement to clean an unmated connector. This flexibility supports patch panels, optical distribution equipment, test equipment and loose patch lead connectors.
The 2.5 mm model has the ordering code SOCC-SC.
The 1.25 mm FibreClick model suits:
LC connectors use a smaller ferrule and compact connector body. Therefore, they require the 1.25 mm FibreClick cleaner rather than the larger SC/FC/ST model.
LC connectivity appears widely in high-density fibre patch panels, network equipment and optical transceiver interfaces. As fibre density increases, access to each connector may become more restricted. For this reason, the cleaner’s narrow profile and extended tip help technicians reach connectors within compact installations.
The 1.25 mm model has the ordering code SOCC-LC.
The FibreClick One-Click Cleaner uses a straightforward mechanical action. When the technician pushes the cleaner into the connector interface, the mechanism advances the internal dry cleaning material across the ferrule end face.
This single push performs the cleaning engagement. Therefore, the technician does not need to handle a separate wipe or manually rotate a cleaning stick across the ferrule.
The one-push design offers several practical benefits:
However, technicians should still use the cleaner carefully. They should keep the tool tip protected when it is not in use, avoid touching the cleaning interface and follow the applicable inspection and cleaning procedure.
FibreClick cleaners use dry cloth material specifically designed for cleaning single-fibre connectors. Therefore, normal use does not require alcohol, cleaning fluid or another solvent.
Dry cleaning provides a convenient first-line method for many common contaminants. In particular, it can remove loose dust and some oils from the ferrule end face. Furthermore, the self-contained format reduces the number of separate cleaning items technicians need to handle at the connector.
The absence of liquid also avoids several problems associated with incorrect solvent use. For example, too much liquid can migrate around the ferrule or leave residue if the fluid does not evaporate cleanly. Likewise, contaminated solvent dispensers or reused wipes can introduce further contamination.
Nevertheless, no single cleaning method resolves every possible contamination condition. Heavy contamination may require a suitable wet-to-dry cleaning process followed by inspection. Therefore, technicians should base the method on the contamination type, inspection result and applicable work procedure.
For routine field work, the One Click Cleaner provides a practical dry-cleaning option. It also complements fibre cleaning wipes, swabs and connector inspection equipment.
Installed connectors often sit behind patch panels, equipment panels, wall outlets or optical distribution frames. Consequently, technicians may not have direct access to the ferrule.
The FibreClick cleaner addresses this problem through its extended cleaning tip. The technician inserts the correct cleaner into the adaptor interface and presses the body forward. The tool then reaches the connector end face positioned on the far side of the adaptor.
This method can support cleaning at:
Cleaning through the adaptor can save time because the technician may not need to remove the connector from the rear of the panel. More importantly, it allows cleaning of interfaces that would otherwise remain difficult to access.
Before use, however, technicians must match the cleaner size to the adaptor. A 2.5 mm cleaner suits compatible SC, FC and ST interfaces, while a 1.25 mm cleaner suits compatible LC and MU interfaces.
Technicians also need to clean connectors that are not installed inside an adaptor. These may include patch lead ends, pigtails, test leads or connectors removed during maintenance.
The FibreClick dust cap supports this application. Once positioned as directed for unmated connector cleaning, the cap acts as an adaptor that helps align the connector with the cleaning mechanism.
This feature allows the same tool to clean:
As a result, technicians do not need one cleaner for panel adaptors and another for accessible connectors of the same ferrule size.
Before cleaning, remove the connector’s protective cap without touching the ferrule. Next, align the connector carefully with the cleaner cap. Then, complete one cleaning engagement. Finally, inspect the connector before mating it.
Each RapidConnect FibreClick One-Click Cleaner provides more than 750 cleaning engagements per unit. Therefore, one cleaner can support substantial installation and maintenance work before replacement.
The actual service period will depend on how frequently the cleaner is used. For example, a technician commissioning a large patching installation may perform many cleaning cycles in one project. In contrast, a maintenance technician may use the cleaner periodically across multiple service visits.
The high engagement count can provide several operational benefits:
Nevertheless, technicians should not continue using a cleaner beyond its available engagements. They should also replace any tool that becomes damaged, contaminated or unable to operate correctly.
A cleaner is a consumable maintenance product. Therefore, businesses should monitor stock levels and keep replacement units available for field technicians, installation teams and test benches.
Fibre connectors do not always sit flush with the equipment surface. Instead, manufacturers may place them inside adaptors, behind faceplates or within recessed equipment ports.
The FibreClick cleaner includes an extended tip that helps reach these recessed interfaces. Consequently, the tool can access many connectors that would prove difficult to clean with a flat wipe or an incorrectly sized swab.
The extended design also supports controlled alignment. Rather than attempting to reach the ferrule manually, the technician guides the cleaner into the compatible adaptor opening.
This feature becomes particularly valuable in:
However, technicians should never force the cleaner into an incompatible or obstructed interface. If the tip does not align correctly, remove it and confirm the connector type, ferrule size and port condition.
RapidConnect FibreClick cleaners can support fibre cleaning across many communication and data environments. Their portable format makes them suitable for field technicians, installers, network operators and fibre test teams.
Typical applications include:
The cleaner does not depend on a particular network speed or optical application. Instead, selection depends primarily on the connector and adaptor format. Therefore, the same 1.25 mm cleaner may support LC connections across several network environments, while the 2.5 mm cleaner may support SC, FC and ST connections elsewhere.
New fibre components may collect contamination during manufacturing, transport, storage, handling or installation. Protective caps reduce exposure, but they do not guarantee a clean end face. In fact, the inside of a contaminated cap can transfer debris to the ferrule.
Therefore, technicians should not assume that a new connector is clean. Instead, they should inspect it before mating. If inspection identifies contamination, the technician can use the correct FibreClick cleaner and then reinspect the connector.
During commissioning, cleaning helps produce more reliable test results. Dirty reference leads, launch leads or installed connectors can increase measured loss. Consequently, technicians may waste time investigating cable performance when the actual problem sits at the connector interface.
A consistent process can help:
This approach helps protect both the installed network and the test equipment.
Existing networks also require connector cleanliness. Moves, additions and changes expose interfaces each time a technician disconnects a patch lead. Furthermore, maintenance work may occur in dusty equipment rooms, outdoor cabinets or active industrial environments.
The One Click Cleaner allows technicians to address connector contamination quickly during:
Before reconnecting a fibre, technicians should inspect both sides of the connection where possible. Cleaning only one side may leave contamination on the other surface. Moreover, mating a clean connector to a contaminated one can transfer particles between them.
For that reason, connector hygiene should cover the complete connection rather than only the easiest surface to reach.
Optical testing depends on clean, stable reference connections. A contaminated connector can alter insertion loss readings and introduce inconsistencies between tests.
For example, a technician may receive an unacceptable loss result and disconnect the lead to investigate. If the connector contamination shifts during reconnection, the next result may differ. This variation can make the fault appear intermittent even when the fibre cable remains unchanged.
Cleaning and inspection help isolate genuine network conditions from connector-related errors. Therefore, technicians should keep suitable One Click Cleaners with optical loss test sets, optical time-domain reflectometers, power meters and inspection microscopes.
Test leads require particular attention because they connect to many different network interfaces. If a test lead becomes contaminated, it can spread debris across multiple ports. Accordingly, technicians should inspect test leads frequently and clean them whenever necessary.
Selecting the right cleaner begins with the connector format. Do not choose the tool only by looking at the patch panel or network equipment. Instead, confirm the connector installed inside the adaptor.
| Connector or interface | Ferrule size | FibreClick model | Ordering code |
|---|---|---|---|
| SC | 2.5 mm | FibreClick SC/FC/ST | SOCC-SC |
| FC | 2.5 mm | FibreClick SC/FC/ST | SOCC-SC |
| ST | 2.5 mm | FibreClick SC/FC/ST | SOCC-SC |
| LC | 1.25 mm | FibreClick LC/MU | SOCC-LC |
| MU | 1.25 mm | FibreClick LC/MU | SOCC-LC |
The connector body may look different across these formats, but the cleaner selection follows the ferrule and compatible interface size.
If a toolkit must support both SC and LC networks, include both cleaner models. Similarly, organisations using FC test equipment or ST legacy infrastructure can use the 2.5 mm version alongside their SC cleaning requirements.
Always follow the applicable workplace procedure and any instructions provided with the cleaning and inspection equipment. The following workflow provides a general guide.
Correct alignment matters. Angled or forced insertion may prevent effective cleaning and could damage the cleaner or interface.
After cleaning, do not place the connector on a bench or return it to a contaminated protective cap. Otherwise, the end face may immediately collect more debris.
Cleaning delivers the greatest value when it forms part of a controlled inspection process.
Inspection establishes the connector’s actual condition. It may show that the connector is already clean, or it may reveal dust, oils or other contamination.
Inspection also helps prevent unnecessary cleaning. Although cleaning remains important, technicians should avoid repeatedly operating a cleaner without checking the result.
If inspection identifies contamination, use the correct cleaning tool. A FibreClick One-Click Cleaner provides a convenient dry-cleaning method for compatible single-fibre connectors.
Keep the process controlled. In particular, avoid touching the tool tip, connector ferrule or adaptor interface.
After cleaning, inspect the connector again. This step confirms whether the process removed the contamination. If contamination remains, apply the appropriate approved cleaning method and reinspect.
Once inspection confirms cleanliness, complete the connection promptly. Leaving the connector exposed increases the chance of renewed contamination.
This workflow helps technicians avoid mating dirty connectors and transferring debris across the interface.
Even experienced technicians can introduce contamination through rushed or inconsistent practices. Understanding the most common mistakes helps improve field results.
A protective cap reduces physical exposure, but it does not prove that the connector is clean. Dust or residue may already exist inside the cap. Therefore, inspect the connector rather than relying on the cap alone.
Fingers carry oils and particles. Even brief contact can contaminate the connector end face. Consequently, technicians should handle connectors by their bodies and boots.
Every mated connection contains two surfaces. Cleaning one connector while ignoring the other may leave the interface contaminated. Therefore, inspect both sides wherever access allows.
A wipe can move contamination rather than remove it if the technician reuses a dirty section. A self-contained One Click Cleaner advances its internal material for each engagement, which supports a fresh cleaning action.
A 2.5 mm cleaner should not replace a 1.25 mm cleaner, and vice versa. Choose the model that matches the connector and adaptor.
The cleaner should align smoothly with a compatible interface. If resistance occurs, stop and verify the port. Forcing the tool may damage the cleaner or the fibre interface.
A mechanical engagement does not automatically prove that the connector is clean. Reinspection verifies the result and determines whether additional action is necessary.
An exposed connector can quickly collect airborne contamination. Therefore, mate it promptly or fit a clean protective cap.
SC connectors use a 2.5 mm ferrule and commonly appear in telecommunications, enterprise, broadband and fibre distribution systems. Their push-pull body makes them easy to identify, although colour alone should not determine the cleaning tool.
Use the SOCC-SC 2.5 mm FibreClick cleaner for compatible SC connectors and adaptors.
SC adaptors may contain a connector on the far side of a patch panel or equipment interface. Therefore, the extended cleaner tip allows the technician to reach the installed ferrule through the adaptor opening.
For an unmated SC patch lead, use the cleaner’s cap arrangement. After cleaning, inspect the end face and connect it without touching the ferrule.
LC connectors use a 1.25 mm ferrule and support compact, high-density fibre installations. They appear widely in patch panels, switches, transceivers and data centre infrastructure.
Use the SOCC-LC 1.25 mm FibreClick cleaner for compatible LC connectors and adaptors.
High-density environments can make cleaning difficult because adjacent connectors restrict access. However, the compact cleaner tip helps technicians reach the individual LC interface.
Where an LC connector sits within a duplex clip, technicians must ensure the cleaner aligns with the intended connector. They should avoid twisting or forcing the connector assembly.
FC connectors use a 2.5 mm ferrule and a threaded coupling mechanism. They frequently appear on fibre test instruments, laboratory equipment and some specialised communication systems.
Use the SOCC-SC 2.5 mm FibreClick cleaner for compatible FC connectors and interfaces.
Because FC connectors often appear on test equipment, cleanliness becomes especially important. A contaminated instrument port or reference lead can affect every measurement made through that interface. Therefore, technicians should include inspection and cleaning in their test equipment preparation process.
ST connectors also use a 2.5 mm ferrule. Their bayonet-style coupling remains present in some industrial, campus and legacy fibre networks.
Use the SOCC-SC 2.5 mm FibreClick cleaner for compatible ST connectors and adaptors.
Although ST installations may operate at lower data rates than newer LC-based systems, connector cleanliness still affects optical performance. Therefore, older infrastructure should receive the same disciplined inspection and cleaning process as a new network.
MU connectors use a 1.25 mm ferrule. While less common than LC connectors in many Australian networks, they still require a correctly sized cleaning tool.
Use the SOCC-LC 1.25 mm FibreClick cleaner for compatible MU connectors and adaptors.
As always, confirm the interface before inserting the cleaner. Similar ferrule sizes do not mean every connector body or equipment arrangement provides identical access.
Fibre connectors may use different end-face geometries, including Ultra Physical Contact and Angled Physical Contact designs. These commonly appear as UPC and APC interfaces.
The connector format and ferrule size still determine the required FibreClick model. For example, both SC/UPC and SC/APC connectors use an SC-format 2.5 mm ferrule. Likewise, LC/UPC and LC/APC connectors use an LC-format 1.25 mm ferrule.
However, technicians must never mate UPC and APC connectors together. Their end-face geometries differ, so an incorrect connection can cause poor optical performance and may damage the interface.
Cleaning does not correct a connector mismatch. Therefore, always verify the connector format, polish geometry and adaptor arrangement before making the connection.
The FibreClick cleaner selection depends on the connector and ferrule size rather than whether the fibre is singlemode or multimode.
For example:
Connector colours may help identify fibre or polish types, but colour should not replace positive identification. Different manufacturers and installations may use varying colour conventions.
Cleanliness matters for both singlemode and multimode systems. However, singlemode networks can prove particularly sensitive to contamination because of the small optical core and demanding optical performance requirements.
One Click Cleaners and fibre cleaning wipes serve related but different purposes.
A One Click Cleaner works particularly well for:
Fibre cleaning wipes can support:
Rather than viewing the products as direct substitutes, many technicians carry both. The One Click Cleaner provides convenient dry cleaning, while suitable wipes and cleaning fluid can support more difficult contamination conditions.
Swabs can clean certain adaptor sleeves, equipment interfaces and other recessed fibre components. However, technicians must select the correct swab size and use it according to the applicable procedure.
The FibreClick cleaner provides a controlled mechanical action for compatible single-fibre connector end faces. In contrast, swabs may serve a wider range of specific cleaning tasks depending on their construction and dimensions.
A complete fibre cleaning kit may include:
The correct combination depends on the connector formats and working environment.
Proper storage helps keep the cleaner ready for use.
Technicians should:
A cleaner carried loose in a dirty tool bag may collect contamination around its external surfaces. Therefore, a dedicated fibre cleaning compartment or sealed case provides better protection.
Businesses can improve consistency by documenting a standard connector inspection and cleaning procedure.
The procedure should define:
Training should reinforce the procedure. Furthermore, technicians should understand why cleanliness matters rather than treating cleaning as an optional final step.
A documented approach can also reduce variation between installers. As a result, the organisation gains more consistent testing, commissioning and maintenance outcomes.
| Specification | FibreClick SC/FC/ST | FibreClick LC/MU |
|---|---|---|
| Compatible connectors | SC, FC and ST | LC and MU |
| Compatible interface size | 2.5 mm | 1.25 mm |
| Cleaning method | One-push dry mechanical action | One-push dry mechanical action |
| Cleaning material | Dry cloth cleaner | Dry cloth cleaner |
| Cleaning engagements | More than 750 per unit | More than 750 per unit |
| Dimensions | 15 × 15 × 180 mm | 15 × 15 × 180 mm |
| Weight | 23 g | 22 g |
| Ordering code | SOCC-SC | SOCC-LC |
RapidConnect FibreClick One-Click Cleaner – SC/FC/ST
Choose SOCC-SC for compatible SC, FC and ST connectors and 2.5 mm adaptor interfaces.
RapidConnect FibreClick One-Click Cleaner – LC/MU
Choose SOCC-LC for compatible LC and MU connectors and 1.25 mm adaptor interfaces.
Organisations working across mixed connector environments should consider keeping both models available.
A One Click Cleaner removes dust, oils and other contamination from a compatible fibre connector end face. It uses a mechanical push action to advance dry cleaning material across the ferrule.
SC connectors use a 2.5 mm ferrule. Therefore, select the RapidConnect FibreClick SC/FC/ST model with ordering code SOCC-SC.
LC connectors use a 1.25 mm ferrule. Select the RapidConnect FibreClick LC/MU model with ordering code SOCC-LC.
Yes. The 2.5 mm FibreClick cleaner supports compatible SC, FC and ST connectors and adaptor interfaces.
Yes. The 1.25 mm FibreClick cleaner supports compatible LC and MU connectors and adaptor interfaces.
Each FibreClick One-Click Cleaner provides more than 750 cleaning engagements per unit.
No. The cleaner uses a dry cloth cleaning material and does not require alcohol or cleaning fluid for its normal dry-cleaning action.
Yes. The extended tip allows the appropriate FibreClick model to clean compatible connectors installed inside adaptors, faceplates and bulkheads.
Yes. The dust cap acts as an adaptor for cleaning compatible unmated connectors.
Yes, wherever suitable inspection equipment and procedures allow. Inspection identifies contamination and establishes whether cleaning is required.
Yes. Reinspection confirms whether the cleaning process successfully removed contamination.
Yes, provided the connector format and ferrule size match the cleaner. The cleaner selection depends on the connector interface rather than the fibre type.
No. LC connectors use a 1.25 mm ferrule and require the 1.25 mm LC/MU cleaner.
No. A cap protects the connector from some environmental exposure, but it cannot guarantee cleanliness. Contamination may exist inside the cap or on the ferrule.
Yes, where access and procedures allow. A clean connector can become contaminated when mated with a dirty connector.
Cleaning may correct a test failure when connector contamination causes excess loss or unstable results. However, it will not correct fibre damage, connector mismatch, poor termination or other network faults.
The One Click Cleaner Knowledge Centre provides focused guidance across fibre contamination, connector inspection, cleaning methods, tool selection and network maintenance. As the Knowledge Centre expands, each section will help installers and network operators protect connector performance throughout the complete fibre lifecycle.
First, this section explains why fibre connector cleanliness matters, how contamination affects an optical interface and why technicians should never assume that a capped connector is clean.
Articles coming soon.
Next, this section explores the inspect–clean–inspect process. In particular, it will explain how inspection supports consistent cleaning decisions and helps prevent contaminated connectors from entering service.
Articles coming soon.
This section will provide connector-specific guidance for selecting and using 2.5 mm and 1.25 mm cleaning tools. Furthermore, it will examine common access challenges across patch panels, adaptors, equipment ports and unmated connectors.
Articles coming soon.
Different contaminants may require different cleaning methods. Therefore, this section will compare dry mechanical cleaning with wet-to-dry procedures and explain when each approach may be appropriate.
Articles coming soon.
Test leads and instrument interfaces can spread contamination across many network ports. Accordingly, this section will focus on inspection, cleaning and handling practices for optical test equipment and reference connections.
Articles coming soon.
Finally, this section will compare One Click Cleaners, fibre cleaning wipes, cleaning swabs and other maintenance products. It will also help technicians build practical cleaning kits for field, workshop and commissioning work.
Articles coming soon.
A fibre connection can only perform reliably when its connector interfaces remain clean and correctly mated. Therefore, technicians need cleaning tools that suit the connectors they work with and fit naturally into installation and maintenance procedures.
RapidConnect FibreClick One-Click Cleaners provide:
Whether commissioning a new fibre network, testing an existing link or maintaining active equipment, the correct One Click Cleaner helps make connector hygiene faster and more consistent.
Anderson Corporation supplies RapidConnect FibreClick One-Click Cleaners for SC, FC, ST, LC and MU fibre connector formats.
Choose SOCC-SC for compatible 2.5 mm SC, FC and ST connections. Alternatively, choose SOCC-LC for compatible 1.25 mm LC and MU connections. For mixed fibre environments, keep both versions available so technicians can clean the principal connector formats encountered across the network.
Contact Anderson Corporation for pricing, availability or assistance selecting the correct One Click Cleaner for your fibre installation, testing or maintenance requirements.
Check out the official Anderson Corporation YouTube Channel for more useful Fibre Optic Information!
